Logo
收藏本站 | 留言反馈
客服热线:400-060-1557
邢台市乐众机械制造有限公司专业生产各种砂浆喷涂机,了解最新砂浆喷涂机价格、细石混凝土输送泵视频请致电:18231930999
砂浆喷涂机 您的位置:首页- 产品展示 - 砂浆喷涂机
砂浆喷涂机 点击查看原图

砂浆喷涂机

浏览次数: 次 更新日期:15-11-06

产品详细介绍:

 

1、每班开机前,先按动手油泵数次向传动部位注油。
2、接通电源后,先电动主电机,检查橡胶 螺旋旋转方向是否一致,如不一致,即要调换电源相线(每次重新接电源时都要进行此项检查)
3、接好输送软管及喷头,向料斗加入清水5L,启动电机将清水泵出,以湿润料斗,泵体及输送软管,将水大部分泵出后即停机。
4、向料斗内加入腻子或涂料即可开机喷涂(应先启动空压机并打开风阀)
5、严禁料斗内无料、无水的状态下空转。
6、工作完毕要排尽料斗内余料,并向料斗内注足够的清水,清洗料斗,并开机泵出,清洗软管及喷头,直到泵出的全是清水,以免余料在软管种凝固,堵塞软管及喷头。
7、停机时间过久,将机器擦拭干净,并卸下增压螺杆,涂油后,妥善保管,使用时重新安装。
8、工作中出现泵出压力不足,可调整增压定子螺栓或更换增压胶套及增压蜗杆。
9、喷涂前,应将受喷面积用水渗透;喷射时喷头尽量垂直与受喷面(距离可根据喷涂效果自行调整)分层均匀喷涂,并和收平工序协调进行。墙面过干或喷涂后时间过久会严重影响收平效果,要改变工艺。
10、向料斗内装料要均匀,不能间断,当输送螺旋旋转时,严禁用棍棒在料斗内搅拌,以防伤人。
11、喷浆输送管一旦堵塞,将开关转换到手动位置,只开压缩机,将泵头前快速接头卸下,而后将喷头朝下堵实,风压产生反向压力,将输送管余浆吹出,在将快速接头装上,开始正常工作。
12、喷射手操作时,应佩戴安全帽,防护眼镜、防护服等防护用品。
13、增压胶套和增压螺杆为易损件,为延长使用寿命,在初次使用时,增压定子螺栓更处于松散状态,待压力降低,流量明显减少时在调整压紧螺栓,使之处于正常工作状况。

 

1, each class before the start, first by the hand pump to several oil transmission parts.
2, after the power is switched on, the first main electric motor, check the rubber screw rotation direction is consistent, if not consistent, that is, to change the power phase (time to re connect the power of the test)
3, good transport hose and nozzle, the hopper to join the 5L, the starting motor will be clear water pump, to wet the hopper, pump body and conveying hose, the majority of the water out of the pump.
4, in addition to the hopper putty or spraying paint can boot (should be the first to start the air compressor and open air valve)
5, is strictly prohibited in the hopper without material, anhydrous state under idling.
6, the work is done to the discharge hopper, and to the hopper of sufficient water, clean the hopper, and start the pump out, clean the hose and nozzle, until the pump out of the whole water, so as not to rest in the hose type of solidification, plug the hose and nozzle.
7, stop for a long time, wipe clean the machine, and remove the pressure screw, oiling, safekeeping, use re installation.
8, work in the emergence of a shortage of pump pressure, can adjust the pressure of the stator bolts or replace the booster pressure rubber and rubber cover.
9, spraying before, should be subject to the spray area of water penetration; spray nozzle as far as possible vertical and the surface (distance can be adjusted according to the effect of spraying) stratified uniform spraying, and the process of coordination. Wall over dry or spraying after a long time will seriously affect the effect of the leveling effect, to change the process.
10, to the hopper loading should be uniform, can not be stopped, when the conveying spiral rotation, it is strictly prohibited to whisk in the hopper with sticks, to prevent injury.
11, spray delivery pipe once the plug, switch switch to manual position, just open the compressor, pump head quick connector to unload, then head down plugging, wind pressure produce reverse pressure, the conveying pipe residual slurry blow out, the quick connector is installed on, began to work normally.
12, when the shooter, should wear a helmet, protective glasses, protective clothing and other protective equipment.
13, booster rubber sleeve and booster screw for wearing parts, in order to extend the service life, in the first time, the booster stator bolts are in a loose state, when the pressure is reduced, the flow is significantly reduced in the adjustment of the bolts, so that the normal working condition.

上一产品: 无气喷涂机
下一产品: 细石泵

相关产品介绍

柱塞式砂浆喷涂机
柱塞式砂浆喷涂机
311快速喷涂机
311快速喷涂机
打点拉毛喷涂机
打点拉毛喷涂机
砂浆喷涂机
砂浆喷涂机
无气喷涂机
无气喷涂机

关于我们| 资质证书 | 留言反馈 | 联系我们 | 网站地图

Copyright © 2013. www.zeliangjixie.com All Rights Reserved 版权所有 邢台市乐众机械制造有限公司
地址:河北省邢台市任县西黄工业区 电话:0319-7588597  13722935900(郭经理) 传真:0319-7588597

赛富通邢台运营中心【邢台智睿网络】 提供技术支持